| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130 |
- menuconfig LEDS_TRIGGERS
- bool "LED Trigger support"
- depends on LEDS_CLASS
- help
- This option enables trigger support for the leds class.
- These triggers allow kernel events to drive the LEDs and can
- be configured via sysfs. If unsure, say Y.
- if LEDS_TRIGGERS
- config LEDS_TRIGGER_TIMER
- tristate "LED Timer Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled by a programmable timer
- via sysfs. Some LED hardware can be programmed to start
- blinking the LED without any further software interaction.
- For more details read Documentation/leds/leds-class.txt.
- If unsure, say Y.
- config LEDS_TRIGGER_ONESHOT
- tristate "LED One-shot Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to blink in one-shot pulses with parameters
- controlled via sysfs. It's useful to notify the user on
- sporadic events, when there are no clear begin and end trap points,
- or on dense events, where this blinks the LED at constant rate if
- rearmed continuously.
- It also shows how to use the led_blink_set_oneshot() function.
- If unsure, say Y.
- config LEDS_TRIGGER_DISK
- bool "LED Disk Trigger"
- depends on IDE_GD_ATA || ATA
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled by disk activity.
- If unsure, say Y.
- config LEDS_TRIGGER_MTD
- bool "LED MTD (NAND/NOR) Trigger"
- depends on MTD
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled by MTD activity.
- If unsure, say N.
- config LEDS_TRIGGER_HEARTBEAT
- tristate "LED Heartbeat Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled by a CPU load average.
- The flash frequency is a hyperbolic function of the 1-minute
- load average.
- If unsure, say Y.
- config LEDS_TRIGGER_BACKLIGHT
- tristate "LED backlight Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled as a backlight device: they
- turn off and on when the display is blanked and unblanked.
- If unsure, say N.
- config LEDS_TRIGGER_CPU
- bool "LED CPU Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled by active CPUs. This shows
- the active CPUs across an array of LEDs so you can see which
- CPUs are active on the system at any given moment.
- If unsure, say N.
- config LEDS_TRIGGER_GPIO
- tristate "LED GPIO Trigger"
- depends on LEDS_TRIGGERS
- depends on GPIOLIB || COMPILE_TEST
- help
- This allows LEDs to be controlled by gpio events. It's good
- when using gpios as switches and triggering the needed LEDs
- from there. One use case is n810's keypad LEDs that could
- be triggered by this trigger when user slides up to show
- keypad.
- If unsure, say N.
- config LEDS_TRIGGER_DEFAULT_ON
- tristate "LED Default ON Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be initialised in the ON state.
- If unsure, say Y.
- comment "iptables trigger is under Netfilter config (LED target)"
- depends on LEDS_TRIGGERS
- config LEDS_TRIGGER_TRANSIENT
- tristate "LED Transient Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows one time activation of a transient state on
- GPIO/PWM based hardware.
- If unsure, say Y.
- config LEDS_TRIGGER_CAMERA
- tristate "LED Camera Flash/Torch Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be controlled as a camera flash/torch device.
- This enables direct flash/torch on/off by the driver, kernel space.
- If unsure, say Y.
- config LEDS_TRIGGER_PANIC
- bool "LED Panic Trigger"
- depends on LEDS_TRIGGERS
- help
- This allows LEDs to be configured to blink on a kernel panic.
- Enabling this option will allow to mark certain LEDs as panic indicators,
- allowing to blink them on a kernel panic, even if they are set to
- a different trigger.
- If unsure, say Y.
- endif # LEDS_TRIGGERS
|
