lbwww/site/docs/install/ivy_has_common.md

---

title: Insert vendor files on Sandybridge/Ivybridge/Haswell x-toc-enable: true ...

Please make sure to install build dependencies if following this guide, and note that this guide assumes you use lbmk.git, not the release archives, even if you're using release ROM images, which is fine.

Coreboot is nominally free software, but requires certain vendor code on some boards, for certain functionalities; we cover this more thoroughly in the Freedom Status page and in the Binary Blob Reduction Policy.

Therefore, you should just follow this guide if in any doubt. Otherwise, the freedom status page lists all boards that require vendor files, and it says what they are. This is because Libreboot cannot directly distribute some of them, but they are extracted from vendor updates at build time, and inserted into images; when those images are then archived for release, the non-redistributable filejs are removed.

The same logic can be used after the fact, to re-download and re-insert these files; the page that you're reading now will tell you how to do so.

If in doubt, just follow these instructions anyway; if your board doesn't need vendor files inserted, nothing will happen. You only need to follow this guide if you use release ROMs; if you're building directly from source, using the Libreboot build system, then you can just flash the result.

Injecting vendor files into ROM

You must determine the correct board name, for your board, based on the list generated when running this command:

./mk -b coreboot list

In order to inject the necessary files into a rom image, run the script from the root of lbmk and point to the rom image.

If you only wish to flash a release rom then the process of injecting the necessary files is quite simple. Run the injection script pointing to the release archive you downloaded:

./vendor inject libreboot-RELEASE_targetname.tar.xz

You are strongly advised only to insert it on the tarball, because then checksums are verified to ensure that the vendor files were inserted correctly. Otherwise, you can do it manually on each individual image, specifying the board name with the instructions provided below:

The script can automatically detect the board as long as you do not change the file name. You can then find flash-ready ROMs in /bin/release/

Alternatively, you may patch only a single rom file, but you must supply the correct board target name as alluded to above. For example:

./vendor inject -r x230_libreboot.rom -b x230_12mb

Optionally, you can use this script to modify the mac address of the rom with the -m flag. For example:

./vendor inject -r x230_libreboot.rom -b x230_12mb -m 00:f6:f0:40:71:fd

Check that the files were inserted

You must ensure that the files were inserted. The inject command automatically verifies checksums of the complete images, when you run it directly on a release tarball, but not when running it manually on an individual image; checking it manually is useful for the latter, but you should probably just insert it into the tarball.

Some examples of how to do that in lbmk:

./mk -d coreboot TREENAME

TREENAME should be the coreboot tree corresponding to your board. Check this in config/coreboot/BOARD/target.cfg for your board, and tree will be set to e.g. default, or some other tree name.

Now you find elf/cbfstool, which is a directory containing cbfstool and ifdtool. Do this on your ROM image (libreboot.rom in the example below):

./elf/cbfstool/TREENAME/cbfstool libreboot.rom print

You should check that the files were inserted in cbfs, if needed; for example, EC firmware or MRC firmware.

Next:

./elf/ifdtool/TREENAME/ifdtool -x libreboot.rom

This creates several .bin files, one of which says me in it (Intel ME). Run hexdump on it:

hexdump flashregion_2_intel_me.bin

Check the output. If it's all 0xFF (all ones) or otherwise isn't a bunch of code, then the Intel ME firmware wasn't inserted.

You'll note the small size of the Intel ME, e.g. 84KB on sandybridge platforms. This is because lbmk automatically neuters it, disabling it during early boot. This is done using me_cleaner, which lbmk imports.

NOTE: the MAC changer makes use of nvmutil, which you can read more about in the nvmutil documentation.

Errata

NOTE: As of Libreboot releases from May 2024 onward, the Intel MRC is no longer included for Haswell; MRC is a blob for raminit, but we now provide libre raminit. The following targets no longer exist in the build system:

• t440pmrc_12mb (use t440plibremrc_12mb instead)
• t440pbmrc_12mb (use t440plibremrc_12mb instead)
• w541mrc_12mb (use w541_12mb instead)
• w541bmrc_12mb (use w541_12mb instead)
• dell9020sff_12mb (use dell9020sff_nri_12mb instead)
• dell9020sffbmrc (use dell9020sff_nri_12mb instead)
• dell9020mt_12mb (use dell9020mt_nri_12mb instead)
• dell9020mtbmrc (use dell9020mt_nri_12mb instead)

This is written as errata because some users may still be using older release images but on the newer build system from May 2024 onward; you must use the Libreboot 20240225 release if you want to inject MRC and so on, for these older targets.

Libreboot's binary blob reduction policy is very strict, and states: if a blob can be avoided, it must be avoided. Therefore, the MRC is removed on Haswell and Libreboot will only use the libre raminit (called NRI, short for Native Ram Initialisation).