rpi_setup.md 8.5 KB
title: How to program an SPI flash chip with the Raspberry Pi ...
This document exists as a guide for reading from or writing to an SPI flash chip with the Raspberry Pi, using the flashrom software. Most revisions of the RPi should work.
The Libreboot project recommends using blobless GNU+Linux on the Raspberry Pi, to avoid having to run non-free software. This only became possible in February 2017 and the instructions below are not yet updated with the necessary steps, so please do not follow the steps below unless you are willing to run non-free software on your Raspberry Pi.
This only covers SOIC-8 flash chips, for now. SOIC-16 guide coming later (for now, it should be easy enough for you to figure this out for SOIC-16).
Raspberry Pi (ThinkPad X60/T60 and Macbook 2,1)
The Raspberry Pi (a $25 single board computer - SBC) can be used as a 25xx flashing tool.
Disassembling the ThinkPad
Follow the X60 Hardware Maintenance Manual or T60 Hardware Maintenance Manual to disassemble the laptop, until you can access the 25xx flash chip.
For photos, follow the Libreboot T60 Recovery Guide.
On the X60, the 25xx flash chip is on the bottom of the motherboard, under a layer of protective black tape.
On the T60, the 25xx flash chip is just under the palmrest, but blocked by a magnesium frame (which you will have to remove).
Pomona Clip Pinout
Diagram of the 26 GPIO Pins of the Raspberry Pi Model B (for the Model B+ with 40 pins, start counting from the right and leave 14 pins):
25xx flash location in X60 (APPLIES ONLY TO X60!):
~~~~ LCD (Front) ~~~~
8765
----
| |
----
1234
~~~ Palmrest (back) ~~
Pin # 25xx signal Raspberry Pi
1 CS 24 2 MISO 21 3 not used not used 4 GND 25 5 MOSI 19 6 CLK 23 7 not used not used 8 3.3V
Make sure the pinouts are correct; otherwise, Flashrom will fail to
detect a chip, or it will "detect" a 0x0 chip. Finally, make sure
that the Pomona clip makes contact with the metal wires of the chip. It
can be a challenge, but keep trying.
How to supply power to the flash chip
There are two ways to supply power to the chip: plugging in an AC adapter (without turning the laptop on), and using the 8th 3.3v pin.
Never connect both the 8th pin and the AC adapter at the same time.
Reading the Flashchip
First, visually inspect (with a magnifying glass) the type of flashchip on the motherboard.
Next, download and install latest flashrom on the Raspberry Pi.
sudo apt-get install build-essential pciutils usbutils libpci-dev libusb-dev libftdi1 libftdi-dev zlib1g-dev subversion libusb-1.0-0-dev flashrom
sudo modprobe spi_bcm2708
sudo modprobe spidev
Run this command to see if 25xx flash is detected
sudo ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000
If flash chip is detected you may try flashing Libreboot now.
Flashing Libreboot
Note: replace /path/to/libreboot.rom with the location of your chosen ROM,
such as ../bin/x60/libreboot_usqwerty.rom):
Next, run this command:
sudo ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000 -w /path/to/libreboot.rom
Once that command outputs the following, the flash has completed successfully. If not, just flash again.
Reading old flash chip contents... done.
Erasing and writing flash chip... Erase/write done.
Verifying flash... VERIFIED.
Sources
- Scruss - Simple ADC with the RaspberryPi
- Flashing coreboot on a T60 with a Raspberry Pi - the_unconventional's blog
Raspberry Pi (ThinkPad X200)
Requirements:
- Raspberry Pi and peripherals
- Relevant SOIC clip
- 6 female - female jumpers
- Internet connection
- Screw drivers
Follow the ThinkPad X200: Initial installation guide to disassemble the laptop, and access the 25xx flash chip.
If you're running Raspian, you can do sudo raspi-config, enable SPI under Advanced and then spidev will be enabled. Simple, eh?
Download Libreboot from their releases page. For your safety, verify the GPG signature as well.
$ gpg --keyserver prefered.keyserver.org --recv-keys 0x656F212E
$ for signature in $(ls *.sig); do gpg --verify $signature; done
Chip model name
Pinout. You may want to download the image so you can zoom in on the text.
Pin # 25xx signal Raspberry Pi Pin #
1 not used not used 2 3.3V 1 3 not used not used 4 not used not used 5 not used not used 6 not used not used 7 CS# 24 8 MISO 21 9 not used not used 10 GND 25 11 not used not used 12 not used not used 13 not used not used 14 not used not used 15 MOSI 19 16 SCLK 23
Note: The raspberry pi 3.3V rail is not sufficient to power the board during flashing, so external power supply might be required.
At this point connect your SOIC clip to the flash chip before powering on your Pi.
Power on your Pi, and run the following. Ensure you swap out "your_chip_name" with the proper name/model of your chip. Check that it can be read successfully. If you cannot read the chip and receive an error similar to "no EEPROM Detected" then you may want to make sure that MISO/MOSI are not swapped around, check with multimeter whether voltage is right and that ground is connected between "programmer" and target.
pi# cd ~/flashrom
pi# ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000 --chip <your_chip_name> -r romread1.rom
pi# ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000 --chip <your_chip_name> -v romread1.rom
pi# ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000 --chip <your_chip_name> -v romread1.rom
If they are identical (verified) then you can generally assume that you get same data each time (which might be bogus).
pi# ./flashrom -p linux_spi:dev=/dev/spidev0.0,spispeed=2000 --chip <your_chip_name> -w libreboot.rom
It may fail a couple times, but keep at it and when you get the message
Verifying flash... Verified or
Warning: Chip content is identical to the requested image then you're
done.
Shut down your pi, put your box back together, and run memtest before instaling operating system
Sources
- Pomona SOIC Clip flashing
- Use a DIY DIP System to flash an desoldered 25xx flash chip
Copyright © 2014, 2015 Lawrence Wu sagnessagiel@gmail.com\ Copyright © 2015 snuffeluffegus <>\ Copyright © 2015 Kevin Keijzer <>\ Copyright © 2016 Leah Rowe info@minifree.org
This page is available under the CC BY SA 4.0