| 12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849505152535455565758596061626364656667686970717273747576 |
- NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
- Required properties:
- - compatible : For Tegra20, must be one of "nvidia,tegra20-i2c-dvc" or
- "nvidia,tegra20-i2c". For Tegra30, must be "nvidia,tegra30-i2c".
- For Tegra114, must be "nvidia,tegra114-i2c". Otherwise, must be
- "nvidia,<chip>-i2c", plus at least one of the above, where <chip> is
- tegra124, tegra132, or tegra210.
- Details of compatible are as follows:
- nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
- controller. This only support master mode of I2C communication. Register
- interface/offset and interrupts handling are different than generic I2C
- controller. Driver of DVC I2C controller is only compatible with
- "nvidia,tegra20-i2c-dvc".
- nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
- master and slave mode of I2C communication. The i2c-tegra driver only
- support master mode of I2C communication. Driver of I2C controller is
- only compatible with "nvidia,tegra20-i2c".
- nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
- very much similar to Tegra20 I2C controller with additional feature:
- Continue Transfer Support. This feature helps to implement M_NO_START
- as per I2C core API transfer flags. Driver of I2C controller is
- compatible with "nvidia,tegra30-i2c" to enable the continue transfer
- support. This is also compatible with "nvidia,tegra20-i2c" without
- continue transfer support.
- nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
- very much similar to Tegra30 I2C controller with some hardware
- modification:
- - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
- fast-clk. Tegra114 has only one clock source called as div-clk and
- hence clock mechanism is changed in I2C controller.
- - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
- default and there is no way to disable it. Tegra114 has this
- interrupt disable by default and SW need to enable explicitly.
- Due to above changes, Tegra114 I2C driver makes incompatible with
- previous hardware driver. Hence, tegra114 I2C controller is compatible
- with "nvidia,tegra114-i2c".
- - reg: Should contain I2C controller registers physical address and length.
- - interrupts: Should contain I2C controller interrupts.
- - address-cells: Address cells for I2C device address.
- - size-cells: Size of the I2C device address.
- - clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
- - clock-names: Must include the following entries:
- Tegra20/Tegra30:
- - div-clk
- - fast-clk
- Tegra114:
- - div-clk
- - resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
- - reset-names: Must include the following entries:
- - i2c
- - dmas: Must contain an entry for each entry in clock-names.
- See ../dma/dma.txt for details.
- - dma-names: Must include the following entries:
- - rx
- - tx
- Example:
- i2c@7000c000 {
- compatible = "nvidia,tegra20-i2c";
- reg = <0x7000c000 0x100>;
- interrupts = <0 38 0x04>;
- #address-cells = <1>;
- #size-cells = <0>;
- clocks = <&tegra_car 12>, <&tegra_car 124>;
- clock-names = "div-clk", "fast-clk";
- resets = <&tegra_car 12>;
- reset-names = "i2c";
- dmas = <&apbdma 16>, <&apbdma 16>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
|
