cbwww/site/docs/install/ga-g41m-es2l.md

---

title: Gigabyte GA-G41M-ES2L desktop board ...

<<<<<<< HEAD This guide is for those who want Canoeboot on their Intel GA-G41M-ES2L

motherboard while they still have the original BIOS present.

GA-G41M-ES2L | ***Specifications*** | | |----------------------------|------------------------------------------------| | **Manufacturer** | Gigabyte | | **Name** | GA-G41M-ES2L | | **Released** | 2009 | | **Chipset** | Intel G41 | | **CPU** | Intel Core 2 Extreme/Quad/Duo, Pentium Extreme/D/4 Extreme/4/Celeron | | **Graphics** | Integrated | | **Display** | None. | | **Memory** | Up to 8GB (2x4GB DDR2-800) | | **Architecture** | x86_64 | | **Original boot firmware** | AWARD BIOS | | **Intel ME/AMD PSP** | Present. Can be disabled | | **Flash chip** | 2x8Mbit | ``` W+: Works without blobs; N: Doesn't work; W*: Works with blobs; U: Untested; P+: Partially works; P*: Partially works with blobs ``` | ***Features*** | | |----------------|---------------------------------------| | **Internal flashing with original boot firmware** | W+ | | **Display** | - | | **Audio** | W+ | | **RAM Init** | P+ | | **External output** | P+ | | **Display brightness** | - | | ***Payloads supported*** | | |---------------------------|-------| | **GRUB** | Slow! | | **SeaBIOS** | Works | | **SeaBIOS with GRUB** | Works |

Introduction

This is a desktop board using intel hardware (circa ~2009, ICH7 southbridge, similar performance-wise to the ThinkPad X200. It can make for quite a nifty desktop. Powered by Canoeboot.

IDE on the board is untested, but it might be possible to use a SATA HDD using an IDE SATA adapter. The SATA ports do work, but it's IDE emulation. The emulation is slow in DMA mode sia SeaBIOS, so SeaBIOS is configured to use PIO mode on this board. This SeaBIOS configuration does not affect the Linux kernel.

You need to set a custom MAC address in Linux for the NIC to work. In /etc/network/interfaces on debian-based systems like Debian or Devuan, this would be in the entry for your NIC:\ hwaddress ether macaddressgoeshere

Alternatively:

cbfstool canoeboot.rom extract -n rt8168-macaddress -f rt8168-macaddress

Modify the MAC address in the file rt8168-macaddress and then:

cbfstool canoeboot.rom remove -n rt8168-macaddress
cbfstool canoeboot.rom add -f rt8168-macaddress -n rt8168-macaddress -t raw

Now you have a different MAC address hardcoded. In the above example, the ROM image is named canoeboot.rom for your board. You can find cbfstool under cbutils/ after running the following command in the build system:

./mk -d coreboot TREENAME

You can learn more about using the build system, cbmk, here:\ Canoeboot build instructions

RAM

This board is very picky with RAM. If it doesn't boot, try an EHCI debug dongle, serial usb adapter and null modem cable, or spkmodem, to get a coreboot log to see if it passed raminit.

Kingston 8 GiB Kit KVR800D2N6/8G with Elpida Chips E2108ABSE-8G-E

this is a 2x4GB setup and these work quite well, according to a user on IRC.

Nanya NT2GT64U8HD0BY-AD with 2 GiB of NT5TU128M8DE-AD chips works too.

Many other modules will probably work just fine, but raminit is very picky on this board. Your mileage will fluctuate, wildly.

09844d62 (simplify docs/install and merge docs/hardware)

MAC ADDRESS

NOTE: due to a bug in the hardware, the MAC address is hardcoded in coreboot. Therefore, you must set your own MAC address in your operating system.

Use macchanger in your distro, to set a valid MAC address. By doing this, your NIC should work nicely.

Flash chip size {#flashchips}

Use this to find out:

flashprog -p internal

Flashing instructions {#clip}

Refer to spi.md for how to set up an SPI programmer for external flashing. You can only externally reprogram one of the chips at a time, and you need to disable the chip that you're not flashing, by connecting 3v3 to /CS of that chip, so you will actually need second test clip or IC pin mini grabber.

NOTE: on GA-G41M-ES2L, the flash shares a common voltage plane with the southbridge, which draws a lot of current. This will cause under-voltage on most SPI flashers, so do not use the 3.3V rail from your flasher. Do not connect +3.3V to the chip. Instead, turn the board on and then turn it off by holding the power button. With the board powered down, but plugged in, there will be a 3.3V supply from the ATX PSU. You can then flash, but DO NOT connect the +3.3V supply from your SPI flasher!

NOTE: You should use a resistor in series, between 1K to 10K ohms, for the 3.3v connection to the CS pin. This is to protect from over-current.

Here is an image of the flash chip:\

Internal flashing is possible. Boot with the proprietary BIOS and GNU+Linux. There are 2 flash chips (one is backup).

Flash the first chip:

./flashprog -p internal:dualbiosindex=0 -w canoeboot.rom

Flash the second chip:

./flashprog -p internal:dualbiosindex=1 -w canoeboot.rom

NOTE: you can still boot the system with just the main flash chip connected, after desoldering the backup chip. This has been tested while Canoeboot was already installed onto the main chip.

NOTE: If you don't flash both chips, the recovery program from the default factory BIOS will kick in and your board will be soft bricked. Make sure that you flash both chips!

NOTE: Canoeboot standardises on flashprog now, as of 3 May 2024, which is a fork of flashrom.