Void-Hardened-Kernel/drivers/usb/host/ohci-pxa27x.c

// SPDX-License-Identifier: GPL-1.0+
/*
 * OHCI HCD (Host Controller Driver) for USB.
 *
 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
 * (C) Copyright 2002 Hewlett-Packard Company
 *
 * Bus Glue for pxa27x
 *
 * Written by Christopher Hoover <ch@hpl.hp.com>
 * Based on fragments of previous driver by Russell King et al.
 *
 * Modified for LH7A404 from ohci-sa1111.c
 *  by Durgesh Pattamatta <pattamattad@sharpsec.com>
 *
 * Modified for pxa27x from ohci-lh7a404.c
 *  by Nick Bane <nick@cecomputing.co.uk> 26-8-2004
 *
 * This file is licenced under the GPL.
 */

#include <linux/clk.h>
#include <linux/device.h>
#include <linux/dma-mapping.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
#include <linux/platform_data/usb-ohci-pxa27x.h>
#include <linux/platform_data/usb-pxa3xx-ulpi.h>
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
#include <linux/signal.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
#include <linux/usb/otg.h>

#include <mach/hardware.h>

#include "ohci.h"

#define DRIVER_DESC "OHCI PXA27x/PXA3x driver"

/*
 * UHC: USB Host Controller (OHCI-like) register definitions
 */
#define UHCREV		(0x0000) /* UHC HCI Spec Revision */
#define UHCHCON		(0x0004) /* UHC Host Control Register */
#define UHCCOMS		(0x0008) /* UHC Command Status Register */
#define UHCINTS		(0x000C) /* UHC Interrupt Status Register */
#define UHCINTE		(0x0010) /* UHC Interrupt Enable */
#define UHCINTD		(0x0014) /* UHC Interrupt Disable */
#define UHCHCCA		(0x0018) /* UHC Host Controller Comm. Area */
#define UHCPCED		(0x001C) /* UHC Period Current Endpt Descr */
#define UHCCHED		(0x0020) /* UHC Control Head Endpt Descr */
#define UHCCCED		(0x0024) /* UHC Control Current Endpt Descr */
#define UHCBHED		(0x0028) /* UHC Bulk Head Endpt Descr */
#define UHCBCED		(0x002C) /* UHC Bulk Current Endpt Descr */
#define UHCDHEAD	(0x0030) /* UHC Done Head */
#define UHCFMI		(0x0034) /* UHC Frame Interval */
#define UHCFMR		(0x0038) /* UHC Frame Remaining */
#define UHCFMN		(0x003C) /* UHC Frame Number */
#define UHCPERS		(0x0040) /* UHC Periodic Start */
#define UHCLS		(0x0044) /* UHC Low Speed Threshold */

#define UHCRHDA		(0x0048) /* UHC Root Hub Descriptor A */
#define UHCRHDA_NOCP	(1 << 12)	/* No over current protection */
#define UHCRHDA_OCPM	(1 << 11)	/* Over Current Protection Mode */
#define UHCRHDA_POTPGT(x) \
			(((x) & 0xff) << 24) /* Power On To Power Good Time */

#define UHCRHDB		(0x004C) /* UHC Root Hub Descriptor B */
#define UHCRHS		(0x0050) /* UHC Root Hub Status */
#define UHCRHPS1	(0x0054) /* UHC Root Hub Port 1 Status */
#define UHCRHPS2	(0x0058) /* UHC Root Hub Port 2 Status */
#define UHCRHPS3	(0x005C) /* UHC Root Hub Port 3 Status */

#define UHCSTAT		(0x0060) /* UHC Status Register */
#define UHCSTAT_UPS3	(1 << 16)	/* USB Power Sense Port3 */
#define UHCSTAT_SBMAI	(1 << 15)	/* System Bus Master Abort Interrupt*/
#define UHCSTAT_SBTAI	(1 << 14)	/* System Bus Target Abort Interrupt*/
#define UHCSTAT_UPRI	(1 << 13)	/* USB Port Resume Interrupt */
#define UHCSTAT_UPS2	(1 << 12)	/* USB Power Sense Port 2 */
#define UHCSTAT_UPS1	(1 << 11)	/* USB Power Sense Port 1 */
#define UHCSTAT_HTA	(1 << 10)	/* HCI Target Abort */
#define UHCSTAT_HBA	(1 << 8)	/* HCI Buffer Active */
#define UHCSTAT_RWUE	(1 << 7)	/* HCI Remote Wake Up Event */

#define UHCHR           (0x0064) /* UHC Reset Register */
#define UHCHR_SSEP3	(1 << 11)	/* Sleep Standby Enable for Port3 */
#define UHCHR_SSEP2	(1 << 10)	/* Sleep Standby Enable for Port2 */
#define UHCHR_SSEP1	(1 << 9)	/* Sleep Standby Enable for Port1 */
#define UHCHR_PCPL	(1 << 7)	/* Power control polarity low */
#define UHCHR_PSPL	(1 << 6)	/* Power sense polarity low */
#define UHCHR_SSE	(1 << 5)	/* Sleep Standby Enable */
#define UHCHR_UIT	(1 << 4)	/* USB Interrupt Test */
#define UHCHR_SSDC	(1 << 3)	/* Simulation Scale Down Clock */
#define UHCHR_CGR	(1 << 2)	/* Clock Generation Reset */
#define UHCHR_FHR	(1 << 1)	/* Force Host Controller Reset */
#define UHCHR_FSBIR	(1 << 0)	/* Force System Bus Iface Reset */

#define UHCHIE          (0x0068) /* UHC Interrupt Enable Register*/
#define UHCHIE_UPS3IE	(1 << 14)	/* Power Sense Port3 IntEn */
#define UHCHIE_UPRIE	(1 << 13)	/* Port Resume IntEn */
#define UHCHIE_UPS2IE	(1 << 12)	/* Power Sense Port2 IntEn */
#define UHCHIE_UPS1IE	(1 << 11)	/* Power Sense Port1 IntEn */
#define UHCHIE_TAIE	(1 << 10)	/* HCI Interface Transfer Abort
					   Interrupt Enable*/
#define UHCHIE_HBAIE	(1 << 8)	/* HCI Buffer Active IntEn */
#define UHCHIE_RWIE	(1 << 7)	/* Remote Wake-up IntEn */

#define UHCHIT          (0x006C) /* UHC Interrupt Test register */

#define PXA_UHC_MAX_PORTNUM    3

static const char hcd_name[] = "ohci-pxa27x";

static struct hc_driver __read_mostly ohci_pxa27x_hc_driver;

struct pxa27x_ohci {
	struct clk	*clk;
	void __iomem	*mmio_base;
	struct regulator *vbus[3];
	bool		vbus_enabled[3];
};

#define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)

/*
  PMM_NPS_MODE -- PMM Non-power switching mode
      Ports are powered continuously.

  PMM_GLOBAL_MODE -- PMM global switching mode
      All ports are powered at the same time.

  PMM_PERPORT_MODE -- PMM per port switching mode
      Ports are powered individually.
 */
static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *pxa_ohci, int mode)
{
	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);
	uint32_t uhcrhdb = __raw_readl(pxa_ohci->mmio_base + UHCRHDB);

	switch (mode) {
	case PMM_NPS_MODE:
		uhcrhda |= RH_A_NPS;
		break;
	case PMM_GLOBAL_MODE:
		uhcrhda &= ~(RH_A_NPS | RH_A_PSM);
		break;
	case PMM_PERPORT_MODE:
		uhcrhda &= ~(RH_A_NPS);
		uhcrhda |= RH_A_PSM;

		/* Set port power control mask bits, only 3 ports. */
		uhcrhdb |= (0x7<<17);
		break;
	default:
		printk( KERN_ERR
			"Invalid mode %d, set to non-power switch mode.\n",
			mode );

		uhcrhda |= RH_A_NPS;
	}

	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
	__raw_writel(uhcrhdb, pxa_ohci->mmio_base + UHCRHDB);
	return 0;
}

static int pxa27x_ohci_set_vbus_power(struct pxa27x_ohci *pxa_ohci,
				      unsigned int port, bool enable)
{
	struct regulator *vbus = pxa_ohci->vbus[port];
	int ret = 0;

	if (IS_ERR_OR_NULL(vbus))
		return 0;

	if (enable && !pxa_ohci->vbus_enabled[port])
		ret = regulator_enable(vbus);
	else if (!enable && pxa_ohci->vbus_enabled[port])
		ret = regulator_disable(vbus);

	if (ret < 0)
		return ret;

	pxa_ohci->vbus_enabled[port] = enable;

	return 0;
}

static int pxa27x_ohci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
				   u16 wIndex, char *buf, u16 wLength)
{
	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
	int ret;

	switch (typeReq) {
	case SetPortFeature:
	case ClearPortFeature:
		if (!wIndex || wIndex > 3)
			return -EPIPE;

		if (wValue != USB_PORT_FEAT_POWER)
			break;

		ret = pxa27x_ohci_set_vbus_power(pxa_ohci, wIndex - 1,
						 typeReq == SetPortFeature);
		if (ret)
			return ret;
		break;
	}

	return ohci_hub_control(hcd, typeReq, wValue, wIndex, buf, wLength);
}
/*-------------------------------------------------------------------------*/

static inline void pxa27x_setup_hc(struct pxa27x_ohci *pxa_ohci,
				   struct pxaohci_platform_data *inf)
{
	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);
	uint32_t uhcrhda = __raw_readl(pxa_ohci->mmio_base + UHCRHDA);

	if (inf->flags & ENABLE_PORT1)
		uhchr &= ~UHCHR_SSEP1;

	if (inf->flags & ENABLE_PORT2)
		uhchr &= ~UHCHR_SSEP2;

	if (inf->flags & ENABLE_PORT3)
		uhchr &= ~UHCHR_SSEP3;

	if (inf->flags & POWER_CONTROL_LOW)
		uhchr |= UHCHR_PCPL;

	if (inf->flags & POWER_SENSE_LOW)
		uhchr |= UHCHR_PSPL;

	if (inf->flags & NO_OC_PROTECTION)
		uhcrhda |= UHCRHDA_NOCP;
	else
		uhcrhda &= ~UHCRHDA_NOCP;

	if (inf->flags & OC_MODE_PERPORT)
		uhcrhda |= UHCRHDA_OCPM;
	else
		uhcrhda &= ~UHCRHDA_OCPM;

	if (inf->power_on_delay) {
		uhcrhda &= ~UHCRHDA_POTPGT(0xff);
		uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2);
	}

	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
	__raw_writel(uhcrhda, pxa_ohci->mmio_base + UHCRHDA);
}

static inline void pxa27x_reset_hc(struct pxa27x_ohci *pxa_ohci)
{
	uint32_t uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR);

	__raw_writel(uhchr | UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
	udelay(11);
	__raw_writel(uhchr & ~UHCHR_FHR, pxa_ohci->mmio_base + UHCHR);
}

#ifdef CONFIG_PXA27x
extern void pxa27x_clear_otgph(void);
#else
#define pxa27x_clear_otgph()	do {} while (0)
#endif

static int pxa27x_start_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
{
	int retval;
	struct pxaohci_platform_data *inf;
	uint32_t uhchr;
	struct usb_hcd *hcd = dev_get_drvdata(dev);

	inf = dev_get_platdata(dev);

	retval = clk_prepare_enable(pxa_ohci->clk);
	if (retval)
		return retval;

	pxa27x_reset_hc(pxa_ohci);

	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) | UHCHR_FSBIR;
	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);

	while (__raw_readl(pxa_ohci->mmio_base + UHCHR) & UHCHR_FSBIR)
		cpu_relax();

	pxa27x_setup_hc(pxa_ohci, inf);

	if (inf->init)
		retval = inf->init(dev);

	if (retval < 0) {
		clk_disable_unprepare(pxa_ohci->clk);
		return retval;
	}

	if (cpu_is_pxa3xx())
		pxa3xx_u2d_start_hc(&hcd->self);

	uhchr = __raw_readl(pxa_ohci->mmio_base + UHCHR) & ~UHCHR_SSE;
	__raw_writel(uhchr, pxa_ohci->mmio_base + UHCHR);
	__raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, pxa_ohci->mmio_base + UHCHIE);

	/* Clear any OTG Pin Hold */
	pxa27x_clear_otgph();
	return 0;
}

static void pxa27x_stop_hc(struct pxa27x_ohci *pxa_ohci, struct device *dev)
{
	struct pxaohci_platform_data *inf;
	struct usb_hcd *hcd = dev_get_drvdata(dev);
	uint32_t uhccoms;

	inf = dev_get_platdata(dev);

	if (cpu_is_pxa3xx())
		pxa3xx_u2d_stop_hc(&hcd->self);

	if (inf->exit)
		inf->exit(dev);

	pxa27x_reset_hc(pxa_ohci);

	/* Host Controller Reset */
	uhccoms = __raw_readl(pxa_ohci->mmio_base + UHCCOMS) | 0x01;
	__raw_writel(uhccoms, pxa_ohci->mmio_base + UHCCOMS);
	udelay(10);

	clk_disable_unprepare(pxa_ohci->clk);
}

#ifdef CONFIG_OF
static const struct of_device_id pxa_ohci_dt_ids[] = {
	{ .compatible = "marvell,pxa-ohci" },
	{ }
};

MODULE_DEVICE_TABLE(of, pxa_ohci_dt_ids);

static int ohci_pxa_of_init(struct platform_device *pdev)
{
	struct device_node *np = pdev->dev.of_node;
	struct pxaohci_platform_data *pdata;
	u32 tmp;
	int ret;

	if (!np)
		return 0;

	/* Right now device-tree probed devices don't get dma_mask set.
	 * Since shared usb code relies on it, set it here for now.
	 * Once we have dma capability bindings this can go away.
	 */
	ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
	if (ret)
		return ret;

	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
		return -ENOMEM;

	if (of_property_read_bool(np, "marvell,enable-port1"))
		pdata->flags |= ENABLE_PORT1;
	if (of_property_read_bool(np, "marvell,enable-port2"))
		pdata->flags |= ENABLE_PORT2;
	if (of_property_read_bool(np, "marvell,enable-port3"))
		pdata->flags |= ENABLE_PORT3;
	if (of_property_read_bool(np, "marvell,port-sense-low"))
		pdata->flags |= POWER_SENSE_LOW;
	if (of_property_read_bool(np, "marvell,power-control-low"))
		pdata->flags |= POWER_CONTROL_LOW;
	if (of_property_read_bool(np, "marvell,no-oc-protection"))
		pdata->flags |= NO_OC_PROTECTION;
	if (of_property_read_bool(np, "marvell,oc-mode-perport"))
		pdata->flags |= OC_MODE_PERPORT;
	if (!of_property_read_u32(np, "marvell,power-on-delay", &tmp))
		pdata->power_on_delay = tmp;
	if (!of_property_read_u32(np, "marvell,port-mode", &tmp))
		pdata->port_mode = tmp;
	if (!of_property_read_u32(np, "marvell,power-budget", &tmp))
		pdata->power_budget = tmp;

	pdev->dev.platform_data = pdata;

	return 0;
}
#else
static int ohci_pxa_of_init(struct platform_device *pdev)
{
	return 0;
}
#endif

/*-------------------------------------------------------------------------*/

/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */


/**
 * ohci_hcd_pxa27x_probe - initialize pxa27x-based HCDs
 * Context: !in_interrupt()
 *
 * Allocates basic resources for this USB host controller, and
 * then invokes the start() method for the HCD associated with it
 * through the hotplug entry's driver_data.
 *
 */
static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
{
	int retval, irq;
	struct usb_hcd *hcd;
	struct pxaohci_platform_data *inf;
	struct pxa27x_ohci *pxa_ohci;
	struct ohci_hcd *ohci;
	struct resource *r;
	struct clk *usb_clk;
	unsigned int i;

	retval = ohci_pxa_of_init(pdev);
	if (retval)
		return retval;

	inf = dev_get_platdata(&pdev->dev);

	if (!inf)
		return -ENODEV;

	irq = platform_get_irq(pdev, 0);
	if (irq < 0) {
		pr_err("no resource of IORESOURCE_IRQ");
		return irq;
	}

	usb_clk = devm_clk_get(&pdev->dev, NULL);
	if (IS_ERR(usb_clk))
		return PTR_ERR(usb_clk);

	hcd = usb_create_hcd(&ohci_pxa27x_hc_driver, &pdev->dev, "pxa27x");
	if (!hcd)
		return -ENOMEM;

	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	hcd->regs = devm_ioremap_resource(&pdev->dev, r);
	if (IS_ERR(hcd->regs)) {
		retval = PTR_ERR(hcd->regs);
		goto err;
	}
	hcd->rsrc_start = r->start;
	hcd->rsrc_len = resource_size(r);

	/* initialize "struct pxa27x_ohci" */
	pxa_ohci = to_pxa27x_ohci(hcd);
	pxa_ohci->clk = usb_clk;
	pxa_ohci->mmio_base = (void __iomem *)hcd->regs;

	for (i = 0; i < 3; ++i) {
		char name[6];

		if (!(inf->flags & (ENABLE_PORT1 << i)))
			continue;

		sprintf(name, "vbus%u", i + 1);
		pxa_ohci->vbus[i] = devm_regulator_get(&pdev->dev, name);
	}

	retval = pxa27x_start_hc(pxa_ohci, &pdev->dev);
	if (retval < 0) {
		pr_debug("pxa27x_start_hc failed");
		goto err;
	}

	/* Select Power Management Mode */
	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);

	if (inf->power_budget)
		hcd->power_budget = inf->power_budget;

	/* The value of NDP in roothub_a is incorrect on this hardware */
	ohci = hcd_to_ohci(hcd);
	ohci->num_ports = 3;

	retval = usb_add_hcd(hcd, irq, 0);
	if (retval == 0) {
		device_wakeup_enable(hcd->self.controller);
		return retval;
	}

	pxa27x_stop_hc(pxa_ohci, &pdev->dev);
 err:
	usb_put_hcd(hcd);
	return retval;
}


/* may be called without controller electrically present */
/* may be called with controller, bus, and devices active */

/**
 * ohci_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs
 * @dev: USB Host Controller being removed
 * Context: !in_interrupt()
 *
 * Reverses the effect of ohci_hcd_pxa27x_probe(), first invoking
 * the HCD's stop() method.  It is always called from a thread
 * context, normally "rmmod", "apmd", or something similar.
 *
 */
static int ohci_hcd_pxa27x_remove(struct platform_device *pdev)
{
	struct usb_hcd *hcd = platform_get_drvdata(pdev);
	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
	unsigned int i;

	usb_remove_hcd(hcd);
	pxa27x_stop_hc(pxa_ohci, &pdev->dev);

	for (i = 0; i < 3; ++i)
		pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);

	usb_put_hcd(hcd);
	return 0;
}

/*-------------------------------------------------------------------------*/

#ifdef CONFIG_PM
static int ohci_hcd_pxa27x_drv_suspend(struct device *dev)
{
	struct usb_hcd *hcd = dev_get_drvdata(dev);
	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
	bool do_wakeup = device_may_wakeup(dev);
	int ret;


	if (time_before(jiffies, ohci->next_statechange))
		msleep(5);
	ohci->next_statechange = jiffies;

	ret = ohci_suspend(hcd, do_wakeup);
	if (ret)
		return ret;

	pxa27x_stop_hc(pxa_ohci, dev);
	return ret;
}

static int ohci_hcd_pxa27x_drv_resume(struct device *dev)
{
	struct usb_hcd *hcd = dev_get_drvdata(dev);
	struct pxa27x_ohci *pxa_ohci = to_pxa27x_ohci(hcd);
	struct pxaohci_platform_data *inf = dev_get_platdata(dev);
	struct ohci_hcd *ohci = hcd_to_ohci(hcd);
	int status;

	if (time_before(jiffies, ohci->next_statechange))
		msleep(5);
	ohci->next_statechange = jiffies;

	status = pxa27x_start_hc(pxa_ohci, dev);
	if (status < 0)
		return status;

	/* Select Power Management Mode */
	pxa27x_ohci_select_pmm(pxa_ohci, inf->port_mode);

	ohci_resume(hcd, false);
	return 0;
}

static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = {
	.suspend	= ohci_hcd_pxa27x_drv_suspend,
	.resume		= ohci_hcd_pxa27x_drv_resume,
};
#endif

static struct platform_driver ohci_hcd_pxa27x_driver = {
	.probe		= ohci_hcd_pxa27x_probe,
	.remove		= ohci_hcd_pxa27x_remove,
	.shutdown	= usb_hcd_platform_shutdown,
	.driver		= {
		.name	= "pxa27x-ohci",
		.of_match_table = of_match_ptr(pxa_ohci_dt_ids),
#ifdef CONFIG_PM
		.pm	= &ohci_hcd_pxa27x_pm_ops,
#endif
	},
};

static const struct ohci_driver_overrides pxa27x_overrides __initconst = {
	.extra_priv_size =      sizeof(struct pxa27x_ohci),
};

static int __init ohci_pxa27x_init(void)
{
	if (usb_disabled())
		return -ENODEV;

	pr_info("%s: " DRIVER_DESC "\n", hcd_name);

	ohci_init_driver(&ohci_pxa27x_hc_driver, &pxa27x_overrides);
	ohci_pxa27x_hc_driver.hub_control = pxa27x_ohci_hub_control;

	return platform_driver_register(&ohci_hcd_pxa27x_driver);
}
module_init(ohci_pxa27x_init);

static void __exit ohci_pxa27x_cleanup(void)
{
	platform_driver_unregister(&ohci_hcd_pxa27x_driver);
}
module_exit(ohci_pxa27x_cleanup);

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:pxa27x-ohci");