linux-phytium/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2016 Andreas Färber
 */

#include "meson-gx.dtsi"
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
#include <dt-bindings/clock/gxbb-clkc.h>
#include <dt-bindings/clock/gxbb-aoclkc.h>
#include <dt-bindings/reset/gxbb-aoclkc.h>

/ {
	compatible = "amlogic,meson-gxbb";

	soc {
		usb0_phy: phy@c0000000 {
			compatible = "amlogic,meson-gxbb-usb2-phy";
			#phy-cells = <0>;
			reg = <0x0 0xc0000000 0x0 0x20>;
			resets = <&reset RESET_USB_OTG>;
			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
			clock-names = "usb_general", "usb";
			status = "disabled";
		};

		usb1_phy: phy@c0000020 {
			compatible = "amlogic,meson-gxbb-usb2-phy";
			#phy-cells = <0>;
			reg = <0x0 0xc0000020 0x0 0x20>;
			resets = <&reset RESET_USB_OTG>;
			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
			clock-names = "usb_general", "usb";
			status = "disabled";
		};

		usb0: usb@c9000000 {
			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
			reg = <0x0 0xc9000000 0x0 0x40000>;
			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
			clock-names = "otg";
			phys = <&usb0_phy>;
			phy-names = "usb2-phy";
			dr_mode = "host";
			status = "disabled";
		};

		usb1: usb@c9100000 {
			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
			reg = <0x0 0xc9100000 0x0 0x40000>;
			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
			clock-names = "otg";
			phys = <&usb1_phy>;
			phy-names = "usb2-phy";
			dr_mode = "host";
			status = "disabled";
		};
	};
};

&aobus {
	pinctrl_aobus: pinctrl@14 {
		compatible = "amlogic,meson-gxbb-aobus-pinctrl";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		gpio_ao: bank@14 {
			reg = <0x0 0x00014 0x0 0x8>,
			      <0x0 0x0002c 0x0 0x4>,
			      <0x0 0x00024 0x0 0x8>;
			reg-names = "mux", "pull", "gpio";
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&pinctrl_aobus 0 0 14>;
		};

		uart_ao_a_pins: uart_ao_a {
			mux {
				groups = "uart_tx_ao_a", "uart_rx_ao_a";
				function = "uart_ao";
			};
		};

		uart_ao_a_cts_rts_pins: uart_ao_a_cts_rts {
			mux {
				groups = "uart_cts_ao_a",
				       "uart_rts_ao_a";
				function = "uart_ao";
			};
		};

		uart_ao_b_pins: uart_ao_b {
			mux {
				groups = "uart_tx_ao_b", "uart_rx_ao_b";
				function = "uart_ao_b";
			};
		};

		uart_ao_b_cts_rts_pins: uart_ao_b_cts_rts {
			mux {
				groups = "uart_cts_ao_b",
				       "uart_rts_ao_b";
				function = "uart_ao_b";
			};
		};

		remote_input_ao_pins: remote_input_ao {
			mux {
				groups = "remote_input_ao";
				function = "remote_input_ao";
			};
		};

		i2c_ao_pins: i2c_ao {
			mux {
				groups = "i2c_sck_ao",
				       "i2c_sda_ao";
				function = "i2c_ao";
			};
		};

		pwm_ao_a_3_pins: pwm_ao_a_3 {
			mux {
				groups = "pwm_ao_a_3";
				function = "pwm_ao_a_3";
			};
		};

		pwm_ao_a_6_pins: pwm_ao_a_6 {
			mux {
				groups = "pwm_ao_a_6";
				function = "pwm_ao_a_6";
			};
		};

		pwm_ao_a_12_pins: pwm_ao_a_12 {
			mux {
				groups = "pwm_ao_a_12";
				function = "pwm_ao_a_12";
			};
		};

		pwm_ao_b_pins: pwm_ao_b {
			mux {
				groups = "pwm_ao_b";
				function = "pwm_ao_b";
			};
		};

		i2s_am_clk_pins: i2s_am_clk {
			mux {
				groups = "i2s_am_clk";
				function = "i2s_out_ao";
			};
		};

		i2s_out_ao_clk_pins: i2s_out_ao_clk {
			mux {
				groups = "i2s_out_ao_clk";
				function = "i2s_out_ao";
			};
		};

		i2s_out_lr_clk_pins: i2s_out_lr_clk {
			mux {
				groups = "i2s_out_lr_clk";
				function = "i2s_out_ao";
			};
		};

		i2s_out_ch01_ao_pins: i2s_out_ch01_ao {
			mux {
				groups = "i2s_out_ch01_ao";
				function = "i2s_out_ao";
			};
		};

		i2s_out_ch23_ao_pins: i2s_out_ch23_ao {
			mux {
				groups = "i2s_out_ch23_ao";
				function = "i2s_out_ao";
			};
		};

		i2s_out_ch45_ao_pins: i2s_out_ch45_ao {
			mux {
				groups = "i2s_out_ch45_ao";
				function = "i2s_out_ao";
			};
		};

		spdif_out_ao_6_pins: spdif_out_ao_6 {
			mux {
				groups = "spdif_out_ao_6";
				function = "spdif_out_ao";
			};
		};

		spdif_out_ao_13_pins: spdif_out_ao_13 {
			mux {
				groups = "spdif_out_ao_13";
				function = "spdif_out_ao";
			};
		};

		ao_cec_pins: ao_cec {
			mux {
				groups = "ao_cec";
				function = "cec_ao";
			};
		};

		ee_cec_pins: ee_cec {
			mux {
				groups = "ee_cec";
				function = "cec_ao";
			};
		};
	};
};

&apb {
	mali: gpu@c0000 {
		compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
		reg = <0x0 0xc0000 0x0 0x40000>;
		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "gp", "gpmmu", "pp", "pmu",
			"pp0", "ppmmu0", "pp1", "ppmmu1",
			"pp2", "ppmmu2";
		clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>;
		clock-names = "bus", "core";

		/*
		 * Mali clocking is provided by two identical clock paths
		 * MALI_0 and MALI_1 muxed to a single clock by a glitch
		 * free mux to safely change frequency while running.
		 */
		assigned-clocks = <&clkc CLKID_GP0_PLL>,
				  <&clkc CLKID_MALI_0_SEL>,
				  <&clkc CLKID_MALI_0>,
				  <&clkc CLKID_MALI>; /* Glitch free mux */
		assigned-clock-parents = <0>, /* Do Nothing */
					 <&clkc CLKID_GP0_PLL>,
					 <0>, /* Do Nothing */
					 <&clkc CLKID_MALI_0>;
		assigned-clock-rates = <744000000>,
				       <0>, /* Do Nothing */
				       <744000000>,
				       <0>; /* Do Nothing */
	};
};

&cbus {
	spifc: spi@8c80 {
		compatible = "amlogic,meson-gxbb-spifc";
		reg = <0x0 0x08c80 0x0 0x80>;
		#address-cells = <1>;
		#size-cells = <0>;
		clocks = <&clkc CLKID_SPI>;
		status = "disabled";
	};
};

&cec_AO {
	clocks = <&clkc_AO CLKID_AO_CEC_32K>;
	clock-names = "core";
};

&clkc_AO {
	compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc";
};

&ethmac {
	clocks = <&clkc CLKID_ETH>,
		 <&clkc CLKID_FCLK_DIV2>,
		 <&clkc CLKID_MPLL2>;
	clock-names = "stmmaceth", "clkin0", "clkin1";
};

&gpio_intc {
	compatible = "amlogic,meson-gpio-intc",
		     "amlogic,meson-gxbb-gpio-intc";
	status = "okay";
};

&hdmi_tx {
	compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
	resets = <&reset RESET_HDMITX_CAPB3>,
		 <&reset RESET_HDMI_SYSTEM_RESET>,
		 <&reset RESET_HDMI_TX>;
	reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
	clocks = <&clkc CLKID_HDMI_PCLK>,
		 <&clkc CLKID_CLK81>,
		 <&clkc CLKID_GCLK_VENCI_INT0>;
	clock-names = "isfr", "iahb", "venci";
};

&sysctrl {
	clkc: clock-controller {
		compatible = "amlogic,gxbb-clkc";
		#clock-cells = <1>;
	};
};

&hwrng {
	clocks = <&clkc CLKID_RNG0>;
	clock-names = "core";
};

&i2c_A {
	clocks = <&clkc CLKID_I2C>;
};

&i2c_AO {
	clocks = <&clkc CLKID_AO_I2C>;
};

&i2c_B {
	clocks = <&clkc CLKID_I2C>;
};

&i2c_C {
	clocks = <&clkc CLKID_I2C>;
};

&periphs {
	pinctrl_periphs: pinctrl@4b0 {
		compatible = "amlogic,meson-gxbb-periphs-pinctrl";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		gpio: bank@4b0 {
			reg = <0x0 0x004b0 0x0 0x28>,
			      <0x0 0x004e8 0x0 0x14>,
			      <0x0 0x00520 0x0 0x14>,
			      <0x0 0x00430 0x0 0x40>;
			reg-names = "mux", "pull", "pull-enable", "gpio";
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&pinctrl_periphs 0 0 119>;
		};

		emmc_pins: emmc {
			mux {
				groups = "emmc_nand_d07",
				       "emmc_cmd",
				       "emmc_clk";
				function = "emmc";
			};
		};

		emmc_ds_pins: emmc-ds {
			mux {
				groups = "emmc_ds";
				function = "emmc";
			};
		};

		emmc_clk_gate_pins: emmc_clk_gate {
			mux {
				groups = "BOOT_8";
				function = "gpio_periphs";
			};
			cfg-pull-down {
				pins = "BOOT_8";
				bias-pull-down;
			};
		};

		nor_pins: nor {
			mux {
				groups = "nor_d",
				       "nor_q",
				       "nor_c",
				       "nor_cs";
				function = "nor";
			};
		};

		spi_pins: spi-pins {
			mux {
				groups = "spi_miso",
					"spi_mosi",
					"spi_sclk";
				function = "spi";
			};
		};

		spi_ss0_pins: spi-ss0 {
			mux {
				groups = "spi_ss0";
				function = "spi";
			};
		};

		sdcard_pins: sdcard {
			mux {
				groups = "sdcard_d0",
				       "sdcard_d1",
				       "sdcard_d2",
				       "sdcard_d3",
				       "sdcard_cmd",
				       "sdcard_clk";
				function = "sdcard";
			};
		};

		sdcard_clk_gate_pins: sdcard_clk_gate {
			mux {
				groups = "CARD_2";
				function = "gpio_periphs";
			};
			cfg-pull-down {
				pins = "CARD_2";
				bias-pull-down;
			};
		};

		sdio_pins: sdio {
			mux {
				groups = "sdio_d0",
				       "sdio_d1",
				       "sdio_d2",
				       "sdio_d3",
				       "sdio_cmd",
				       "sdio_clk";
				function = "sdio";
			};
		};

		sdio_clk_gate_pins: sdio_clk_gate {
			mux {
				groups = "GPIOX_4";
				function = "gpio_periphs";
			};
			cfg-pull-down {
				pins = "GPIOX_4";
				bias-pull-down;
			};
		};

		sdio_irq_pins: sdio_irq {
			mux {
				groups = "sdio_irq";
				function = "sdio";
			};
		};

		uart_a_pins: uart_a {
			mux {
				groups = "uart_tx_a",
				       "uart_rx_a";
				function = "uart_a";
			};
		};

		uart_a_cts_rts_pins: uart_a_cts_rts {
			mux {
				groups = "uart_cts_a",
				       "uart_rts_a";
				function = "uart_a";
			};
		};

		uart_b_pins: uart_b {
			mux {
				groups = "uart_tx_b",
				       "uart_rx_b";
				function = "uart_b";
			};
		};

		uart_b_cts_rts_pins: uart_b_cts_rts {
			mux {
				groups = "uart_cts_b",
				       "uart_rts_b";
				function = "uart_b";
			};
		};

		uart_c_pins: uart_c {
			mux {
				groups = "uart_tx_c",
				       "uart_rx_c";
				function = "uart_c";
			};
		};

		uart_c_cts_rts_pins: uart_c_cts_rts {
			mux {
				groups = "uart_cts_c",
				       "uart_rts_c";
				function = "uart_c";
			};
		};

		i2c_a_pins: i2c_a {
			mux {
				groups = "i2c_sck_a",
				       "i2c_sda_a";
				function = "i2c_a";
			};
		};

		i2c_b_pins: i2c_b {
			mux {
				groups = "i2c_sck_b",
				       "i2c_sda_b";
				function = "i2c_b";
			};
		};

		i2c_c_pins: i2c_c {
			mux {
				groups = "i2c_sck_c",
				       "i2c_sda_c";
				function = "i2c_c";
			};
		};

		eth_rgmii_pins: eth-rgmii {
			mux {
				groups = "eth_mdio",
				       "eth_mdc",
				       "eth_clk_rx_clk",
				       "eth_rx_dv",
				       "eth_rxd0",
				       "eth_rxd1",
				       "eth_rxd2",
				       "eth_rxd3",
				       "eth_rgmii_tx_clk",
				       "eth_tx_en",
				       "eth_txd0",
				       "eth_txd1",
				       "eth_txd2",
				       "eth_txd3";
				function = "eth";
			};
		};

		eth_rmii_pins: eth-rmii {
			mux {
				groups = "eth_mdio",
				       "eth_mdc",
				       "eth_clk_rx_clk",
				       "eth_rx_dv",
				       "eth_rxd0",
				       "eth_rxd1",
				       "eth_tx_en",
				       "eth_txd0",
				       "eth_txd1";
				function = "eth";
			};
		};

		pwm_a_x_pins: pwm_a_x {
			mux {
				groups = "pwm_a_x";
				function = "pwm_a_x";
			};
		};

		pwm_a_y_pins: pwm_a_y {
			mux {
				groups = "pwm_a_y";
				function = "pwm_a_y";
			};
		};

		pwm_b_pins: pwm_b {
			mux {
				groups = "pwm_b";
				function = "pwm_b";
			};
		};

		pwm_d_pins: pwm_d {
			mux {
				groups = "pwm_d";
				function = "pwm_d";
			};
		};

		pwm_e_pins: pwm_e {
			mux {
				groups = "pwm_e";
				function = "pwm_e";
			};
		};

		pwm_f_x_pins: pwm_f_x {
			mux {
				groups = "pwm_f_x";
				function = "pwm_f_x";
			};
		};

		pwm_f_y_pins: pwm_f_y {
			mux {
				groups = "pwm_f_y";
				function = "pwm_f_y";
			};
		};

		hdmi_hpd_pins: hdmi_hpd {
			mux {
				groups = "hdmi_hpd";
				function = "hdmi_hpd";
			};
		};

		hdmi_i2c_pins: hdmi_i2c {
			mux {
				groups = "hdmi_sda", "hdmi_scl";
				function = "hdmi_i2c";
			};
		};

		i2sout_ch23_y_pins: i2sout_ch23_y {
			mux {
				groups = "i2sout_ch23_y";
				function = "i2s_out";
			};
		};

		i2sout_ch45_y_pins: i2sout_ch45_y {
			mux {
				groups = "i2sout_ch45_y";
				function = "i2s_out";
			};
		};

		i2sout_ch67_y_pins: i2sout_ch67_y {
			mux {
				groups = "i2sout_ch67_y";
				function = "i2s_out";
			};
		};

		spdif_out_y_pins: spdif_out_y {
			mux {
				groups = "spdif_out_y";
				function = "spdif_out";
			};
		};
	};
};

&pwrc_vpu {
	resets = <&reset RESET_VIU>,
		 <&reset RESET_VENC>,
		 <&reset RESET_VCBUS>,
		 <&reset RESET_BT656>,
		 <&reset RESET_DVIN_RESET>,
		 <&reset RESET_RDMA>,
		 <&reset RESET_VENCI>,
		 <&reset RESET_VENCP>,
		 <&reset RESET_VDAC>,
		 <&reset RESET_VDI6>,
		 <&reset RESET_VENCL>,
		 <&reset RESET_VID_LOCK>;
	clocks = <&clkc CLKID_VPU>,
	         <&clkc CLKID_VAPB>;
	clock-names = "vpu", "vapb";
	/*
	 * VPU clocking is provided by two identical clock paths
	 * VPU_0 and VPU_1 muxed to a single clock by a glitch
	 * free mux to safely change frequency while running.
	 * Same for VAPB but with a final gate after the glitch free mux.
	 */
	assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
			  <&clkc CLKID_VPU_0>,
			  <&clkc CLKID_VPU>, /* Glitch free mux */
			  <&clkc CLKID_VAPB_0_SEL>,
			  <&clkc CLKID_VAPB_0>,
			  <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
	assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
				 <0>, /* Do Nothing */
				 <&clkc CLKID_VPU_0>,
				 <&clkc CLKID_FCLK_DIV4>,
				 <0>, /* Do Nothing */
				 <&clkc CLKID_VAPB_0>;
	assigned-clock-rates = <0>, /* Do Nothing */
			       <666666666>,
			       <0>, /* Do Nothing */
			       <0>, /* Do Nothing */
			       <250000000>,
			       <0>; /* Do Nothing */
};

&saradc {
	compatible = "amlogic,meson-gxbb-saradc", "amlogic,meson-saradc";
	clocks = <&xtal>,
		 <&clkc CLKID_SAR_ADC>,
		 <&clkc CLKID_SAR_ADC_CLK>,
		 <&clkc CLKID_SAR_ADC_SEL>;
	clock-names = "clkin", "core", "adc_clk", "adc_sel";
};

&sd_emmc_a {
	clocks = <&clkc CLKID_SD_EMMC_A>,
		 <&clkc CLKID_SD_EMMC_A_CLK0>,
		 <&clkc CLKID_FCLK_DIV2>;
	clock-names = "core", "clkin0", "clkin1";
	resets = <&reset RESET_SD_EMMC_A>;
};

&sd_emmc_b {
	clocks = <&clkc CLKID_SD_EMMC_B>,
		 <&clkc CLKID_SD_EMMC_B_CLK0>,
		 <&clkc CLKID_FCLK_DIV2>;
	clock-names = "core", "clkin0", "clkin1";
	resets = <&reset RESET_SD_EMMC_B>;
};

&sd_emmc_c {
	clocks = <&clkc CLKID_SD_EMMC_C>,
		 <&clkc CLKID_SD_EMMC_C_CLK0>,
		 <&clkc CLKID_FCLK_DIV2>;
	clock-names = "core", "clkin0", "clkin1";
	resets = <&reset RESET_SD_EMMC_C>;
};

&spicc {
	clocks = <&clkc CLKID_SPICC>;
	clock-names = "core";
	resets = <&reset RESET_PERIPHS_SPICC>;
	num-cs = <1>;
};

&spifc {
	clocks = <&clkc CLKID_SPI>;
};

&uart_A {
	clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
	clock-names = "xtal", "pclk", "baud";
};

&uart_AO {
	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART1>, <&xtal>;
	clock-names = "xtal", "pclk", "baud";
};

&uart_AO_B {
	clocks = <&xtal>, <&clkc_AO CLKID_AO_UART2>, <&xtal>;
	clock-names = "xtal", "pclk", "baud";
};

&uart_B {
	clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
	clock-names = "xtal", "pclk", "baud";
};

&uart_C {
	clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
	clock-names = "xtal", "pclk", "baud";
};

&vpu {
	compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
	power-domains = <&pwrc_vpu>;
};