123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116 |
- avoid_crossing_perimeters = 0
- bottom_solid_layers = 3
- bridge_acceleration = 0
- bridge_flow_ratio = 1
- bridge_speed = 60
- brim_width = 0
- complete_objects = 0
- default_acceleration = 0
- dont_support_bridges = 1
- external_perimeter_speed = 70%
- external_perimeters_first = 0
- extra_perimeters = 1
- extruder_clearance_height = 20
- extruder_clearance_radius = 20
- extrusion_width = 0
- fill_angle = 45
- fill_density = 30%
- fill_pattern = rectilinear
- first_layer_acceleration = 0
- first_layer_extrusion_width = 125%
- first_layer_height = 0.35
- first_layer_speed = 30%
- gap_fill_speed = 20
- gcode_comments = 0
- infill_acceleration = 0
- infill_every_layers = 1
- infill_extruder = 1
- infill_extrusion_width = 0
- infill_first = 0
- infill_only_where_needed = 0
- infill_speed = 60
- interface_shells = 0
- layer_height = 0.3
- min_skirt_length = 0
- notes =
- only_retract_when_crossing_perimeters = 1
- ooze_prevention = 0
- output_filename_format = [input_filename_base].gcode
- overhangs = 1
- perimeter_acceleration = 0
- perimeter_extruder = 1
- perimeter_extrusion_width = 0
- perimeter_speed = 27
- perimeters = 3
- post_process =
- raft_layers = 0
- resolution = 0
- seam_position = aligned
- skirt_distance = 5
- skirt_height = 1
- skirts = 1
- small_perimeter_speed = 25
- solid_fill_pattern = rectilinear
- solid_infill_below_area = 70
- solid_infill_every_layers = 0
- solid_infill_extrusion_width = 0
- solid_infill_speed = 60
- spiral_vase = 0
- standby_temperature_delta = -5
- support_material = 1
- support_material_angle = 0
- support_material_enforce_layers = 0
- support_material_extruder = 1
- support_material_extrusion_width = 0
- support_material_interface_extruder = 1
- support_material_interface_layers = 3
- support_material_interface_spacing = 0
- support_material_interface_speed = 100%
- support_material_pattern = pillars
- support_material_spacing = 2.5
- support_material_speed = 60
- support_material_threshold = 0
- thin_walls = 1
- threads = 2
- top_infill_extrusion_width = 0
- top_solid_infill_speed = 50
- top_solid_layers = 3
- travel_speed = 120
- bed_size = 140,138
- end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n
- extruder_offset = 0x0
- gcode_flavor = reprap
- layer_gcode =
- nozzle_diameter = 0.375
- print_center = 70,69
- retract_before_travel = 2
- retract_layer_change = 1
- retract_length = 2
- retract_length_toolchange = 10
- retract_lift = 0
- retract_restart_extra = 0
- retract_restart_extra_toolchange = 0
- retract_speed = 30
- start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
- toolchange_gcode =
- use_firmware_retraction = 0
- use_relative_e_distances = 0
- vibration_limit = 0
- wipe = 0
- z_offset = 0
- bed_temperature = 0
- bridge_fan_speed = 100
- cooling = 1
- disable_fan_first_layers = 0
- extrusion_multiplier = 0.74
- fan_always_on = 1
- fan_below_layer_time = 60
- filament_diameter = 1.75
- first_layer_bed_temperature = 0
- first_layer_temperature = 199
- max_fan_speed = 100
- min_fan_speed = 35
- min_print_speed = 10
- slowdown_below_layer_time = 30
- temperature = 198
|