# $XTermId: terminfo,v 1.106 2005/02/06 21:42:38 tom Exp $
#
# $Xorg: terminfo,v 1.3 2000/08/17 19:55:10 cpqbld Exp $
#
# meml locks memory above the cursor; memu unlocks (ala HP terminals)
#
# XFree86 updates/notes/new entries (including xterm-8bit, xterm-16color)
# - Thomas E. Dickey
#
# $XFree86: xc/programs/xterm/terminfo,v 3.55 2005/02/06 21:42:38 dickey Exp $
#
# Special Capabilities:
# --------------------
# ich has a corresponding capability that inserts a single blank.  We could
#	have used ich1=\E[@, which works with ncurses, but that is not standard
#	behavior.  If it is set, then SVr4 vi (e.g., Solaris 2.6) emits both
#	smir/rmir and ich1.
# meml locks memory above the cursor; memu unlocks (ala HP terminals).  This
#	is not recognized by some older (e.g., SVr3) tic programs, but none
#	do more than warn about it.  Ignore the warning.
# smcup clears memory before switching to the alternate screen.  The older
#	(deprecated) \E[?47h did not do this, requiring applications to
#	embed a \E[2J in the rmcup string.  However, that behavior cannot
#	be disabled via titeInhibit, making that resource not function as
#	intended on systems with terminfo.
# rs2/is2 are shorter with XFree86 xterm because it supports DECSTR.  We
#	use the shorter sequence for compatibility with the termcap, which
#	is trimmed to keep it shorter than 1023 characters.  It (escape \E[!p)
#	replaces these in the conventional vt100 reset-string:
#		\E7	- save cursor (fixes origin-mode side-effect)
#		\E[r	- reset scrolling margins
#		\E[m	- reset SGR (including color)
#		\E[?7h	- reset wraparound mode (DECAWM)
#		\E[?1l	- reset application cursor keys (DECCKM)
#		\E[?6l	- reset origin mode (DECOM)
#		\E8	- restore cursor
#	DECSTR is recognized by XFree86 xterm even in vt52 mode.
#
# Editing Keypad:
# --------------
# XFree86 xterm emulates vt220 if the decTerminalID resource is set to 200 or
# higher.  Otherwise it emulates a vt100 or vt52 depending on the value of the
# resource.  When emulating a vt220, we support the editing keypad.  Sun and PC
# keyboards have an editing keypad which is similar to the vt220:
#
#	VT220 editing keypad
#	----------------------------
#	Find      Insert      Remove
#	Select    Prev        Next
#	----------------------------
#
#	Sun/PC editing keypad
#	----------------------------
#	Insert    Home        PageUp
#	Delete    End         PageDn
#	----------------------------
#
# If the sunKeyboard resource is true, we map it this way (adjusting the values
# of Home, End and Delete):
#	VT220		      Sun/PC
#	----------------------------
#	Find		      Home
#	Select		      End
#	Insert		      Insert
#	Remove		      Delete
#	Prev		      PageUp
#	Next		      PageDn
#	----------------------------
#
# Note that all of the keys on the editing keypad transmit escape sequences.  A
# vt220 does this only when in vt220 mode; when emulating a vt100 the editing
# keypad is inactive.
#
# Alternative keycodes:
# --------------------
# Several of the function keys have alternative names, depending on the type of
# host which your xterm is connected to.  DEC (i.e., the VMS system) uses F15
# as the HELP key, F16 as the DO key.  Unix applications generally do not do
# this.  Curses applications in particular, assign a unique keycode to each
# capability string.  These terminal descriptions do not have conflicting
# definitions, to ensure that Unix curses applications use a consistent set of
# keycodes.  To get a VMS-bias, make these substitutions:
#	1. change khome to kfnd
#	2. change kend to kslt
# The original xterm-r6 entry does in fact have a VMS bias.
#
# Some legacy applications using the termcap emulation may expect kll where
# we have specified kend.
#
# Function keys with modifiers (Sun/PC):
# -------------------------------------
#	Shift-Fx          - kf{12+x}
#	Control-Fx        - kf{24+x}
#	Shift-Control-Fx  - kf{36+x}
#
# The terminfo defines some special keys which are documented as "shifted",
# e.g., kDC is shifted-delete-character.
#
# Note however, that even though the terminfo says a key might be sent, there
# may be conflicts which prevent this.  For example, it is common to use
# shifted pageup and pagedown for window manager functions.  The default
# translation for xterm since X11R4 has overridden shifted Insert, Select,
# PageUp and PageDown, which correspond to terminfo kIC, kEND, kPRV and kNXT
# respectively.
#
xterm-new|modern xterm terminal emulator,
	npc,
	indn=\E[%p1%dS,
	kDC=\E[3;2~,
	kEND=\E[1;2F,
	kHOM=\E[1;2H,
	kIC=\E[2;2~,
	kLFT=\E[1;2D,
	kNXT=\E[6;2~,
	kPRV=\E[5;2~,
	kRIT=\E[1;2C,
	kb2=\EOE,
	kcbt=\E[Z,
	kcub1=\EOD,
	kcud1=\EOB,
	kcuf1=\EOC,
	kcuu1=\EOA,
	kend=\EOF,
	kent=\EOM,
	khome=\EOH,
	kich1=\E[2~,
	kmous=\E[M,
	knp=\E[6~,
	kpp=\E[5~,
	rin=\E[%p1%dT,
	use=xterm+pcfkeys,
	use=xterm-basic,
#
xterm+pcfkeys|fragment for PC-style keys,
	kf1=\EOP,
	kf10=\E[21~,
	kf11=\E[23~,
	kf12=\E[24~,
	kf13=\EO2P,
	kf14=\EO2Q,
	kf15=\EO2R,
	kf16=\EO2S,
	kf17=\E[15;2~,
	kf18=\E[17;2~,
	kf19=\E[18;2~,
	kf2=\EOQ,
	kf20=\E[19;2~,
	kf21=\E[20;2~,
	kf22=\E[21;2~,
	kf23=\E[23;2~,
	kf24=\E[24;2~,
	kf25=\EO5P,
	kf26=\EO5Q,
	kf27=\EO5R,
	kf28=\EO5S,
	kf29=\E[15;5~,
	kf3=\EOR,
	kf30=\E[17;5~,
	kf31=\E[18;5~,
	kf32=\E[19;5~,
	kf33=\E[20;5~,
	kf34=\E[21;5~,
	kf35=\E[23;5~,
	kf36=\E[24;5~,
	kf37=\EO6P,
	kf38=\EO6Q,
	kf39=\EO6R,
	kf4=\EOS,
	kf40=\EO6S,
	kf41=\E[15;6~,
	kf42=\E[17;6~,
	kf43=\E[18;6~,
	kf44=\E[19;6~,
	kf45=\E[20;6~,
	kf46=\E[21;6~,
	kf47=\E[23;6~,
	kf48=\E[24;6~,
	kf49=\EO3P,
	kf5=\E[15~,
	kf50=\EO3Q,
	kf51=\EO3R,
	kf52=\EO3S,
	kf53=\E[15;3~,
	kf54=\E[17;3~,
	kf55=\E[18;3~,
	kf56=\E[19;3~,
	kf57=\E[20;3~,
	kf58=\E[21;3~,
	kf59=\E[23;3~,
	kf6=\E[17~,
	kf60=\E[24;3~,
	kf61=\EO4P,
	kf62=\EO4Q,
	kf63=\EO4R,
	kf7=\E[18~,
	kf8=\E[19~,
	kf9=\E[20~,
#
# This chunk is used for building the VT220/Sun/PC keyboard variants.
xterm-basic|modern xterm terminal emulator - common,
	am,
	bce,
	km,
	mc5i,
	mir,
	msgr,
	xenl,
	colors#8,
	cols#80,
	it#8,
	lines#24,
	pairs#64,
	acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
	bel=^G,
	blink=\E[5m,
	bold=\E[1m,
	cbt=\E[Z,
	civis=\E[?25l,
	clear=\E[H\E[2J,
	cnorm=\E[?12l\E[?25h,
	cr=^M,
	csr=\E[%i%p1%d;%p2%dr,
	cub=\E[%p1%dD,
	cub1=^H,
	cud=\E[%p1%dB,
	cud1=^J,
	cuf=\E[%p1%dC,
	cuf1=\E[C,
	cup=\E[%i%p1%d;%p2%dH,
	cuu=\E[%p1%dA,
	cuu1=\E[A,
	cvvis=\E[?12;25h,
	dch=\E[%p1%dP,
	dch1=\E[P,
	dl=\E[%p1%dM,
	dl1=\E[M,
	ech=\E[%p1%dX,
	ed=\E[J,
	el=\E[K,
	el1=\E[1K,
	flash=\E[?5h$<100/>\E[?5l,
	home=\E[H,
	hpa=\E[%i%p1%dG,
	ht=^I,
	hts=\EH,
	ich=\E[%p1%d@,
	il=\E[%p1%dL,
	il1=\E[L,
	ind=^J,
	invis=\E[8m,
	is2=\E[!p\E[?3;4l\E[4l\E>,
	kbs=^H,
	kdch1=\E[3~,
	mc0=\E[i,
	mc4=\E[4i,
	mc5=\E[5i,
	meml=\El,
	memu=\Em,
	op=\E[39;49m,
	rc=\E8,
	rev=\E[7m,
	ri=\EM,
	rmacs=\E(B,
	rmam=\E[?7l,
	rmcup=\E[?1049l,
	rmir=\E[4l,
	rmkx=\E[?1l\E>,
	rmso=\E[27m,
	rmul=\E[24m,
	rs1=\Ec,
	rs2=\E[!p\E[?3;4l\E[4l\E>,
	sc=\E7,
	setab=\E[4%p1%dm,
	setaf=\E[3%p1%dm,
	setb=\E[4%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
	setf=\E[3%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
	sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;%?%p4%t;5%;%?%p7%t;8%;m%?%p9%t\E(0%e\E(B%;,
	sgr0=\E[m\E(B,
	smacs=\E(0,
	smam=\E[?7h,
	smcup=\E[?1049h,
	smir=\E[4h,
	smkx=\E[?1h\E=,
	smso=\E[7m,
	smul=\E[4m,
	tbc=\E[3g,
	u6=\E[%i%d;%dR,
	u7=\E[6n,
	u8=\E[?1;2c,
	u9=\E[c,
	vpa=\E[%i%p1%dd,
# xterm-debian is identical to xterm-new except that it more strictly
# conforms to DEC VT220 behavior in the case of the backspace key; this is
# mandated by the Section 9.8 of the Debian Policy Manual.  Also see
# <http://vt100.net/docs/vt220-rm/>.
xterm-debian|Debian xterm (VT220-conformant backspace),
	kbs=\177,
	use=xterm-new,
#
# The xterm-new description has all of the features, but is not completely
# compatible with vt220.  If you are using a Sun or PC keyboard, set the
# sunKeyboard resource to true:
#	+ maps the editing keypad
#	+ interprets control-function-key as a second array of keys, so a
#	  12-fkey keyboard can support vt220's 20-fkeys.
#	+ maps numeric keypad "+" to ",".
#	+ uses DEC-style control sequences for the application keypad.
#
# Some packagers modify xterm's resource definitions to provide extra function
# keys by using the shift-modifier in the translations resource.  However, that
# interferes with the DECUDK functionality.
#	  
xterm-vt220|xterm emulating vt220,
	ka1=\EOw,
	ka3=\EOy,
	kb2=\EOu,
	kc1=\EOq,
	kc3=\EOs,
	kcbt=\E[Z,
	kcub1=\EOD,
	kcud1=\EOB,
	kcuf1=\EOC,
	kcuu1=\EOA,
	kend=\E[4~,
	kent=\EOM,
	kf1=\EOP,
	kf10=\E[21~,
	kf11=\E[23~,
	kf12=\E[24~,
	kf13=\E[25~,
	kf14=\E[26~,
	kf15=\E[28~,
	kf16=\E[29~,
	kf17=\E[31~,
	kf18=\E[32~,
	kf19=\E[33~,
	kf2=\EOQ,
	kf20=\E[34~,
	kf3=\EOR,
	kf4=\EOS,
	kf5=\E[15~,
	kf6=\E[17~,
	kf7=\E[18~,
	kf8=\E[19~,
	kf9=\E[20~,
	khome=\E[1~,
	kich1=\E[2~,
	kmous=\E[M,
	knp=\E[6~,
	kpp=\E[5~,
	use=xterm-basic,
#
xterm-vt52|xterm emulating dec vt52,
	cols#80,
	it#8,
	lines#24,
	acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
	bel=^G,
	clear=\EH\EJ,
	cr=^M,
	cub1=\ED,
	cud1=\EB,
	cuf1=\EC,
	cup=\EY%p1%' '%+%c%p2%' '%+%c,
	cuu1=\EA,
	ed=\EJ,
	el=\EK,
	home=\EH,
	ht=^I,
	ind=^J,
	kbs=^H,
	kcub1=\ED,
	kcud1=\EB,
	kcuf1=\EC,
	kcuu1=\EA,
	nel=^M^J,
	ri=\EI,
	rmacs=\EG,
	smacs=\EF,
#
# kf30-kf45 are keysyms XK_R1 through XK_R15 on the Sun keyboard.
xterm-sun|xterm with sun function keys,
	kb2=\E[218z,
	kcpy=\E[197z,
	kcub1=\EOD,
	kcud1=\EOB,
	kcuf1=\EOC,
	kcuu1=\EOA,
	kdch1=\E[3~,
	kend=\E[220z,
	kent=\EOM,
	kf1=\E[224z,
	kf10=\E[233z,
	kf11=\E[192z,
	kf12=\E[193z,
	kf13=\E[194z,
	kf14=\E[195z,
	kf15=\E[196z,
	kf17=\E[198z,
	kf18=\E[199z,
	kf19=\E[200z,
	kf2=\E[225z,
	kf20=\E[201z,
	kf3=\E[226z,
	kf31=\E[208z,
	kf32=\E[209z,
	kf33=\E[210z,
	kf34=\E[211z,
	kf35=\E[212z,
	kf36=\E[213z,
	kf38=\E[215z,
	kf4=\E[227z,
	kf40=\E[217z,
	kf42=\E[219z,
	kf44=\E[221z,
	kf5=\E[228z,
	kf6=\E[229z,
	kf7=\E[230z,
	kf8=\E[231z,
	kf9=\E[232z,
	kfnd=\E[200z,
	khlp=\E[196z,
	khome=\E[214z,
	kich1=\E[2z,
	kmous=\E[M,
	knp=\E[222z,
	kpp=\E[216z,
	kund=\E[195z,
	use=xterm-basic,
#
xterm-hp|xterm with hpterm function keys,
	kclr=\EJ,
	kcub1=\ED,
	kcud1=\EB,
	kcuf1=\EC,
	kcuu1=\EA,
	kdch1=\EP,
	kend=\EF,
	kf1=\Ep,
	kf2=\Eq,
	kf3=\Er,
	kf4=\Es,
	kf5=\Et,
	kf6=\Eu,
	kf7=\Ev,
	kf8=\Ew,
	khome=\Eh,
	kich1=\EQ,
	knp=\ES,
	kpp=\ET,
	use=xterm-basic,
xterm-sco|xterm with SCO function keys,
	kcub1=\E[D,
	kcud1=\E[B,
	kcuf1=\E[C,
	kcuu1=\E[A,
	kend=\E[F,
	kf1=\E[M,
	kf10=\E[V,
	kf11=\E[W,
	kf12=\E[X,
	kf13=\E[Y,
	kf15=\E[a,
	kf16=\E[b,
	kf17=\E[c,
	kf18=\E[d,
	kf19=\E[e,
	kf2=\E[N,
	kf20=\E[f,
	kf21=\E[g,
	kf22=\E[h,
	kf23=\E[i,
	kf24=\E[j,
	kf25=\E[k,
	kf26=\E[l,
	kf27=\E[m,
	kf28=\E[n,
	kf29=\E[o,
	kf3=\E[O,
	kf30=\E[p,
	kf31=\E[q,
	kf32=\E[r,
	kf33=\E[s,
	kf34=\E[t,
	kf35=\E[u,
	kf4=\E[P,
	kf5=\E[Q,
	kf6=\E[R,
	kf7=\E[S,
	kf8=\E[T,
	kf9=\E[U,
	khome=\E[H,
	kich1=\E[L,
	knp=\E[G,
	kpp=\E[I,
	use=xterm-basic,
#
# Other variants:
xterm-24|xterms|vs100|xterm terminal emulator (X Window System),
	lines#24,
	use=xterm,
xterm-65|xterm with tall window 65x80 (X Window System),
	lines#65,
	use=xterm,
xterm-bold|xterm with bold instead of underline (X Window System),
	smso=\E[7m,
	smul=\E[1m,
	use=xterm,
xterm-boldso|xterm with bold for standout (X Window System),
	rmso=\E[m,
	smso=\E[1m,
	use=xterm,
xterm-mono|monochrome xterm,
	bce@,
	colors@,
	ncv@,
	pairs@,
	op@,
	setab@,
	setaf@,
	setb@,
	setf@,
	sgr@,
	use=xterm,
#
# VTxxx terminals are usually set up so that full-screen applications will use
# the cursor application mode strings.  This is good for full-screen
# applications, including legacy applications which may have hard-coded
# behavior, but bad for interactive shells (e.g., tcsh, bash) which use arrow
# keys to scroll through a history of command strings.
#
# To see the difference between normal/application modes, consider this example:
#	+ In normal (non-application) mode, the terminal transmits a down-arrow
#	  as \E[C, which happens to echo as a down-arrow.
#	+ In application mode the terminal transmits \EOC, which echoes as C.
#	  That is because the \EO is the SS3 control, which says to use the
#	  character from the G3 character set for the next cell.
# 
# One example of hard-coded behavior would be for applications written to work
# with VT52 and VT100 terminals.  If the application's parser ignores 'O' and
# '?' characters after the escape, then the cursor and keypad strings for the
# two terminals are the same.  (Indeed, one of the first curses applications
# which I used did something like this to cover "ANSI" terminals -TD).
#
# To make this work (leaving the cursor keys in normal mode), we have to adjust
# the terminal initialization sequences:
#
#	smkx/rmkx set/reset the cursor and keypad application modes.  We retain
#		the latter (otherwise many applications fail).
#
#	smcup/rmcup set/restore cursor-addressing mode for full-screen
#		applications.  For xterm, this normally means the alternate
#		screen, which is not compatible with interactive shells.  Some
#		programs are "smart" and disable these.
#
xterm-noapp|xterm with cursor keys in normal mode,
	kcub1=\E[D,
	kcud1=\E[B,
	kcuf1=\E[C,
	kcuu1=\E[A,
	rmcup@,
	rmkx=\E>,
	smcup@,
	smkx=\E=,
	use=xterm,
#
# This should work for the commonly used "color xterm" variations (XFree86
# xterm, color_xterm, nxterm, rxvt).  Note that it does not set 'bce', so for
# XFree86 and and rxvt, some applications that use colors will be less
# efficient, and in a few special cases (with "smart" optimization) the wrong
# color will be painted in spots.
xterm-color|generic "ANSI" color xterm (X Window System),
	colors#8,
	ncv@,
	pairs#64,
	op=\E[m,
	setab=\E[4%p1%dm,
	setaf=\E[3%p1%dm,
	use=xterm-r6,
#
# vi may work better with this entry, because vi
# doesn't use insert mode much
xterm-ic|xterm-vi|xterm with insert character instead of insert mode,
	mir@,
	ich=\E[%p1%d@,
	ich1=\E[@,
	rmir@,
	smir@,
	use=xterm,
#
# This is used only for testing (it's not relevant to DEC VTxxx terminals, but
# to ncurses).
xterm-xmc|xterm with magic-cookie glitch,
	xmc#1,
	use=xterm-new,
#
# This one also is primarily for testing ncurses; while the ISO 6429 defines
# the REP control, none of the DEC VTxxx terminals (VT52 through VT420) support
# it.
xterm-rep|xterm with repeat-character control,
	rep=%p1%c\E[%p2%{1}%-%db,
	use=xterm-new,
#
# This is mainly for testing xterm; the real VT220 will not let you switch
# character sets without first altering the keyboard language in the setup
# screen.  Some emulators allow this anyway.  (Note that these strings are
# normally used only for printers).  The parameter to csnm and scs is the same
# in both cases:  the keyboard language parameter returned by CSI ? 2 6 n.
xterm-nrc|xterm with VT220 national replacement character sets,
	csnm=%?%p1%{1}%=%tNorth American%e%p1%{2}%=%tBritish%e%p1%{3}%=%tFlemish%e%p1%{4}%=%tFrench Canadian%e%p1%{5}%=%tDanish%e%p1%{6}%=%tFinnish%e%p1%{7}%=%tGerman%e%p1%{8}%=%tDutch%e%p1%{9}%=%tItalian%e%p1%{10}%=%tSwiss (French)%e%p1%{11}%=%tSwiss (German)%e%p1%{12}%=%tSwedish%e%p1%{13}%=%tNorwegian%e%p1%{14}%=%tFrench/Belgian%e%p1%{15}%=%tSpanish%;,
	scs=%?%p1%{1}%=%t\E(B%e%p1%{2}%=%t\E(A%e%p1%{3}%=%t\E(R%e%p1%{4}%=%t\E(9%e%p1%{5}%=%t\E(E%e%p1%{6}%=%t\E(5%e%p1%{7}%=%t\E(K%e%p1%{8}%=%t\E(4%e%p1%{9}%=%t\E(Y%e%p1%{10}%=%t\E(=%e%p1%{11}%=%t\E(=%e%p1%{12}%=%t\E(7%e%p1%{13}%=%t\E(E%e%p1%{14}%=%t\E(R%e%p1%{15}%=%t\E(Z%;,
	use=xterm-new,
#
# Foreground 0-15 maps (with toggles) into 30-37 & 90-97
# Background 0-15 maps (with toggles) into 40-47 & 100-107
#
# Originally I suppressed setaf/setab, since ANSI specifies only 8 colors, but
# Stephen Marley persuaded me to allow the "ANSI" color controls to extend to
# 16 colors.  (Note that ncurses 4.2 uses setf/setb from this description;
# however 5.0 selects either according to their availability).  - T.Dickey
#
# SVr4 curses does not use more than 8 colors anyway, so using 16 colors is
# either for terminfo-level applications or via ncurses.
xterm-16color|xterm with 16 colors,
	colors#16,
	ncv#32,
	pairs#256,
	setab=\E[%?%p1%{8}%<%t%p1%{40}%+%e%p1%{92}%+%;%dm,
	setaf=\E[%?%p1%{8}%<%t%p1%{30}%+%e%p1%{82}%+%;%dm,
	setb=%p1%{8}%/%{6}%*%{4}%+\E[%d%p1%{8}%m%Pa%?%ga%{1}%=%t4%e%ga%{3}%=%t6%e%ga%{4}%=%t1%e%ga%{6}%=%t3%e%ga%d%;m,
	setf=%p1%{8}%/%{6}%*%{3}%+\E[%d%p1%{8}%m%Pa%?%ga%{1}%=%t4%e%ga%{3}%=%t6%e%ga%{4}%=%t1%e%ga%{6}%=%t3%e%ga%d%;m,
	use=xterm-new,
#
# This uses RGB values 0..1000
#
# 256 colors should give 65536 pairs, but terminfo stores numbers in a signed
# short.  Most people will not notice problems with only 32767 pairs.
xterm-256color|xterm with 256 colors,
	ccc,
	colors#256,
	pairs#32767,
	initc=\E]4;%p1%d;rgb\:%p2%{255}%*%{1000}%/%2.2X/%p3%{255}%*%{1000}%/%2.2X/%p4%{255}%*%{1000}%/%2.2X\E\\,
	setab=\E[48;5;%p1%dm,
	setaf=\E[38;5;%p1%dm,
	setb=\E[48;5;%p1%dm,
	setf=\E[38;5;%p1%dm,
	use=xterm-new,
xterm-88color|xterm with 88 colors,
	colors#88,
	pairs#7744,
	use=xterm-256color,
#
# This is an 8-bit version of xterm, which emulates DEC vt220 with ANSI color.
# To use it, your decTerminalID resource must be set to 200 or above, and the
# sunKeyboard resource set to true.
#
#	HTS	\E H	\210
#	RI	\E M	\215
#	SS3	\E O	\217
#	CSI	\E [	\233
#
xterm-8bit|xterm terminal emulator with 8-bit controls (X Window System),
	am,
	bce,
	km,
	mc5i,
	mir,
	msgr,
	npc,
	xenl,
	colors#8,
	cols#80,
	it#8,
	lines#24,
	pairs#64,
	acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
	bel=^G,
	blink=\2335m,
	bold=\2331m,
	cbt=\233Z,
	civis=\233?25l,
	clear=\233H\2332J,
	cnorm=\233?25l\233?25h,
	cr=^M,
	csr=\233%i%p1%d;%p2%dr,
	cub=\233%p1%dD,
	cub1=^H,
	cud=\233%p1%dB,
	cud1=^J,
	cuf=\233%p1%dC,
	cuf1=\233C,
	cup=\233%i%p1%d;%p2%dH,
	cuu=\233%p1%dA,
	cuu1=\233A,
	cvvis=\233?12;25h,
	dch=\233%p1%dP,
	dch1=\233P,
	dl=\233%p1%dM,
	dl1=\233M,
	ech=\233%p1%dX,
	ed=\233J,
	el=\233K,
	el1=\2331K,
	flash=\233?5h$<100/>\233?5l,
	home=\233H,
	hpa=\233%i%p1%dG,
	ht=^I,
	hts=\210,
	ich=\233%p1%d@,
	il=\233%p1%dL,
	il1=\233L,
	ind=^J,
	invis=\2338m,
	is2=\E[62"p\E G\233m\233?7h\E>\E7\233?1;3;4;6l\2334l\233r\E8,
	ka1=\217w,
	ka3=\217u,
	kb2=\217y,
	kbeg=\217E,
	kbs=^H,
	kc1=\217q,
	kc3=\217s,
	kcbt=\233Z,
	kcub1=\217D,
	kcud1=\217B,
	kcuf1=\217C,
	kcuu1=\217A,
	kdch1=\2333~,
	kend=\2334~,
	kent=\217M,
	kf1=\23311~,
	kf10=\23321~,
	kf11=\23323~,
	kf12=\23324~,
	kf13=\23325~,
	kf14=\23326~,
	kf15=\23328~,
	kf16=\23329~,
	kf17=\23331~,
	kf18=\23332~,
	kf19=\23333~,
	kf2=\23312~,
	kf20=\23334~,
	kf3=\23313~,
	kf4=\23314~,
	kf5=\23315~,
	kf6=\23317~,
	kf7=\23318~,
	kf8=\23319~,
	kf9=\23320~,
	khome=\2331~,
	kich1=\2332~,
	kmous=\233M,
	knp=\2336~,
	kpp=\2335~,
	mc0=\233i,
	mc4=\2334i,
	mc5=\2335i,
	meml=\El,
	memu=\Em,
	op=\23339;49m,
	rc=\E8,
	rev=\2337m,
	ri=\215,
	rmacs=\E(B,
	rmam=\233?7l,
	rmcup=\233?1049l,
	rmir=\2334l,
	rmkx=\233?1l\E>,
	rmso=\23327m,
	rmul=\23324m,
	rs1=\Ec,
	rs2=\E[62"p\E G\233m\233?7h\E>\E7\233?1;3;4;6l\2334l\233r\E8,
	sc=\E7,
	setab=\2334%p1%dm,
	setaf=\2333%p1%dm,
	setb=\2334%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
	setf=\2333%?%p1%{1}%=%t4%e%p1%{3}%=%t6%e%p1%{4}%=%t1%e%p1%{6}%=%t3%e%p1%d%;m,
	sgr=\2330%?%p6%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;%?%p4%t;5%;%?%p7%t;8%;m%?%p9%t\E(0%e\E(B%;,
	sgr0=\233m\E(B,
	smacs=\E(0,
	smam=\233?7h,
	smcup=\233?1049h,
	smir=\2334h,
	smkx=\233?1h\E=,
	smso=\2337m,
	smul=\2334m,
	tbc=\2333g,
	u6=\233[%i%d;%dR,
	u7=\E[6n,
	u8=\233[?1;2c,
	u9=\E[c,
	vpa=\233%i%p1%dd,
#
# Compatible with the R6 xterm, with the following changes:
#	+ added acsc (perhaps some versions of tic assume the standard vt100
#	  alternate character set)
#	+ added u6, u7, u8, u9 strings for Daniel Weaver's tack program.
#	+ added kmous string for ncurses.
#	+ added khome/kend strings (which conflict with kfnd/kslt, see note).
xterm-r6|xterm-old|xterm X11R6 version,
	am,
	km,
	mir,
	msgr,
	xenl,
	cols#80,
	it#8,
	lines#24,
	acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
	bel=^G,
	blink@,
	bold=\E[1m,
	clear=\E[H\E[2J,
	cr=^M,
	csr=\E[%i%p1%d;%p2%dr,
	cub=\E[%p1%dD,
	cub1=^H,
	cud=\E[%p1%dB,
	cud1=^J,
	cuf=\E[%p1%dC,
	cuf1=\E[C,
	cup=\E[%i%p1%d;%p2%dH,
	cuu=\E[%p1%dA,
	cuu1=\E[A,
	dch=\E[%p1%dP,
	dch1=\E[P,
	dl=\E[%p1%dM,
	dl1=\E[M,
	ed=\E[J,
	el=\E[K,
	enacs=\E)0,
	home=\E[H,
	ht=^I,
	il=\E[%p1%dL,
	il1=\E[L,
	ind=^J,
	is2=\E[m\E[?7h\E[4l\E>\E7\E[r\E[?1;3;4;6l\E8,
	kbs=^H,
	kcub1=\EOD,
	kcud1=\EOB,
	kcuf1=\EOC,
	kcuu1=\EOA,
	kdch1=\E[3~,
	kend=\E[4~,
	kf1=\E[11~,
	kf10=\E[21~,
	kf11=\E[23~,
	kf12=\E[24~,
	kf13=\E[25~,
	kf14=\E[26~,
	kf15=\E[28~,
	kf16=\E[29~,
	kf17=\E[31~,
	kf18=\E[32~,
	kf19=\E[33~,
	kf2=\E[12~,
	kf20=\E[34~,
	kf3=\E[13~,
	kf4=\E[14~,
	kf5=\E[15~,
	kf6=\E[17~,
	kf7=\E[18~,
	kf8=\E[19~,
	kf9=\E[20~,
	khome=\E[1~,
	kich1=\E[2~,
	kmous=\E[M,
	knp=\E[6~,
	kpp=\E[5~,
	meml=\El,
	memu=\Em,
	rc=\E8,
	rev=\E[7m,
	ri=\EM,
	rmacs=^O,
	rmcup=\E[2J\E[?47l\E8,
	rmir=\E[4l,
	rmkx=\E[?1l\E>,
	rmso=\E[m,
	rmul=\E[m,
	rs2=\E[m\E[?7h\E[4l\E>\E7\E[r\E[?1;3;4;6l\E8,
	sc=\E7,
	sgr0=\E[m,
	smacs=^N,
	smcup=\E7\E[?47h,
	smir=\E[4h,
	smkx=\E[?1h\E=,
	smso=\E[7m,
	smul=\E[4m,
	tbc=\E[3g,
	u6=\E[%i%d;%dR,
	u7=\E[6n,
	u8=\E[?1;2c,
	u9=\E[c,
#
# Compatible with the R5 xterm, with the following changes:
#	+ changed 'blink=@', to 'blink@' (the former meant that "@" would start
#	  a blink, the latter that it is not supported).
#	+ changed kf1 through kf4 to correspond with actual usage.  Though X
#	  supports keypad symbols for PF1 to PF4, and xterm interprets these
#	  correctly, the F1 to F4 codes are commonly (but incorrectly) used.
#	+ moved reset string from rs1 to rs2, to correlate better with termcap.
#	+ make khome consistent with other entries.
#	+ use rmul/smul, rmir/smir from termcap, but not rmcup/smcup because
#	  not everyone wants the alternate screen.
#	+ added u6, u7, u8, u9 strings for Daniel Weaver's tack program.
#	+ added kmous string for ncurses.
xterm-r5|xterm R5 version,
	am,
	km,
	msgr,
	xenl,
	cols#80,
	it#8,
	lines#24,
	bel=^G,
	blink@,
	bold=\E[1m,
	clear=\E[H\E[2J,
	cr=^M,
	csr=\E[%i%p1%d;%p2%dr,
	cub=\E[%p1%dD,
	cub1=^H,
	cud=\E[%p1%dB,
	cud1=^J,
	cuf=\E[%p1%dC,
	cuf1=\E[C,
	cup=\E[%i%p1%d;%p2%dH,
	cuu=\E[%p1%dA,
	cuu1=\E[A,
	dch=\E[%p1%dP,
	dch1=\E[P,
	dl=\E[%p1%dM,
	dl1=\E[M,
	ed=\E[J,
	el=\E[K,
	home=\E[H,
	ht=^I,
	hts=\EH,
	ich=\E[%p1%d@,
	ich1=\E[@,
	il=\E[%p1%dL,
	il1=\E[L,
	ind=^J,
	kbs=^H,
	kcub1=\EOD,
	kcud1=\EOB,
	kcuf1=\EOC,
	kcuu1=\EOA,
	kdch1=\E[3~,
	kdl1=\E[31~,
	kel=\E[8~,
	kend=\E[4~,
	kf0=\EOq,
	kf1=\E[11~,
	kf10=\E[21~,
	kf11=\E[23~,
	kf12=\E[24~,
	kf2=\E[12~,
	kf3=\E[13~,
	kf4=\E[14~,
	kf5=\E[15~,
	kf6=\E[17~,
	kf7=\E[18~,
	kf8=\E[19~,
	kf9=\E[20~,
	khome=\E[1~,
	kich1=\E[2~,
	kil1=\E[30~,
	kmous=\E[M,
	knp=\E[6~,
	kpp=\E[5~,
	rc=\E8,
	rev=\E[7m,
	ri=\EM,
	rmir=\E[4l,
	rmkx=\E[?1l\E>,
	rmso=\E[m,
	rmul=\E[m,
	rs2=\E>\E[?1;3;4;5;6l\E[4l\E[?7h\E[m\E[r\E[2J\E[H,
	sc=\E7,
	sgr=\E[%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;m,
	sgr0=\E[m,
	smir=\E[4h,
	smkx=\E[?1h\E=,
	smso=\E[7m,
	smul=\E[4m,
	tbc=\E[3g,
	u6=\E[%i%d;%dR,
	u7=\E[6n,
	u8=\E[?1;2c,
	u9=\E[c,
#
# Customization begins here.
xterm-xfree86|xterm terminal emulator (XFree86),
	use=xterm-new,
#
# This is the only entry which you should have to customize, since "xterm"
# is widely used for a variety of incompatible terminal emulations including
# color_xterm and rxvt.
xterm|X11 terminal emulator,
	use=xterm-debian,
#	use=xterm-new,
#	use=xterm-r6,
